Tag: ls2

Blog, Gallery, Main, Video

2JZGarage – Supra 2JZGTE VVTi Project Update

Well it’s been a while since I’ve posted up any info on my own supra. Unfortunately the supra and this website sometimes become lowest on the list of life’s priorities, but that doesn’t mean I’m still working on the supra – A man must have his hobbies!

Current power;

  • Tuned on pump 98 fuel with a result of 445rwkw (597rwhp) @ 23.5 psi
  • Tuned on pump e85 with a result of 482rwkw (646rwhp) @ 23.5 psi

Since the last update these are the major changes;

  • Titan 272 VVTi Camshafts, GSC Valve stems, GSC beehive springs and titanium retainers – hopefully a write up coming soon on installing these
  • New LS2 LQ9 coil setup, which you can see HERE
  • Swapped out the old Garrett T51R SPL BB with a new Garrett GTX 4088R turbo with 1.06 rear. This was primarily to make it more streetable with the current engine setup staying stock for a while
  • Exhaust camshaft timing adjustments and slight vvti intake cam adjustment made by my tuner – this dramatically improved mid-range with the turbo by around 40hp – Exhaust cam tuning was 2 degrees of retard from memory
  • TRD Seibon hood removed and stock hood put back on to try and improve bonnet lift while racing at high speeds – although I still managed to brake another shroud at around 270kph (167mph)
  • Flex fuel sensor installed, although wiring yet to be setup and tuning to be complete
  • Tial BOV and other exhaust fabrication work for new turbo
  • Driveshaft shop single piece drive shaft, B series diff, Solid diff bushings to reduce axle tramp
  • Powersteering cooler setup in RHD duct
  • TRD sway bars and new links
  • New clamps for FMIC, fittings and ducting
  • Probably a few other things here and there that I’ve forgot about

Next in line will be cleaning up a few things I’m not 100% happy with at the moment such as improving intake temps. I will be installing twin thermo fans due to radiator setup and high speed racing causing shrouds to break – this will require some further intake fabrication work. Would like to create a custom airbox, install a fabricated oil catch can, changing to a new boost solenoid to allow for launch control/boost by gear and fix up some wiring.

New GTX4088R turbo got installed, managed to tap out a boost fitting and have a local shop do some fabrication work

The Titan 272 VVTi Camshafts, GSC Valve stems, GSC beehive springs and titanium retainers getting installed, I will be putting lots more pictures up and explaining this process in the near future

IMG_3780

(more…)

Resources, Tech Articles

LS2 LQ9 Coil Installation

UPDATE – 420kw @ 24.5psi, big thanks to Rick @ Mojo performance and Glen @ ESP Racing Queanbeyan, dyno sheets listed below. This made another 30rwkw+ (40rwhp+) on very similar boost.

UPDATE 2 – Thanks to Steve at Torque Toyota for the attached diagram below of the 2JZGTE VVTi ignition wiring to match the Mojo kit.

Mojo_VVTi_Wiring

UPDATE 3 – The car has since made 486kw @ 24.5psi on e85.

____________________________________________

After many months of troubleshooting my ignition issues as seen in this post HERE I finally came to the realisation that the stock igniter setup wasn’t going to work with my requirements. I didn’t want any complicated aftermarket igniter or alternative solutions so I did some further research and came across the LS2 LQ9 kit from Mojo Performance. After reading some great reviews on supraforums –  I ended up purchasing them.

Rick from Mojo Performance was great to deal with, gave plenty of support and info and was very responsive via email considering the time differences between Australia and the US! In short it is a great bit of kit, easy to install, clear instructions and they resolved my ignition issues and I no longer have any break up of ignition on the road, although I’m yet to get back to the dyno and push it to it’s limits, this is where I used to get the worst issues.

Below is some basic installation steps on the kit for my 2JZGTE VVTi, I haven’t gone into the wiring too much as the diagrams are provided and will vary depending on your setup and aftermarket ECU, but there is the diagram above (See – UPDATE 2) to assist for stock setups . For those wanting to run the coils on the stock ECU you will need to purchase an additional module to generate an IGF signal for it to work correctly. The kit is available for 2JZGE and 2JZGTE non-vvti and vvti.

Some specific notes to my installation – I used the stock igniter wiring by cutting off the existing stock connector and soldering loom, I used the stock noise filter, I hid it away down near the front shock tower. The coils were wired in wasted spark, 3x ViPEC V88 ECU outputs used to drive them, this is possible as each coil has an igniter, but as always please refer to your specific ECU setup and wiring requirements. Currently running 3.5ms dwell.

This is the what is provided in the kit, all required hardware, quality wiring looms and instructions with wiring diagrams
2880

(more…)